Specializing in Silicon Solutions

Blog

Silicone cord buying guide: types, sizes & how to choose the right one


Release time:

2026-10-30

Author:

Dichuang New Materials

Article overview

This guide covers silicone cord types, temperature grades, Shore A hardness selection, UK certifications (WRAS, BS EN 45545, RoHS), material comparisons, and UK sourcing advice. Designed for procurement engineers and DIY buyers at the selection stage.

What is silicone cord?

Silicone cord is a continuous-length extruded profile made from vulcanised silicone rubber, typically circular in cross-section, offering exceptional flexibility, heat resistance, and chemical inertness across a temperature range of -60°C to +300°C. It is manufactured from high-purity polydimethylsiloxane (PDMS) polymer that has been compounded with reinforcing fillers and cured — either by peroxide or platinum-catalysed processes — to produce the final elastic structure.

Understanding what you are actually buying matters more than most buyers realise. Silicone rubber cord is often grouped alongside generic rubber cord or elastic cord in supplier catalogues, yet its performance envelope is fundamentally different. Why do so many procurement teams end up with the wrong specification? Because the label "silicone" covers everything from low-grade peroxide-cured profiles to precision medical-grade extrusions. The distinction affects service life, compliance, and total cost of ownership.

According to recent 2026 data from Grand View Research, the global silicone rubber market is valued at approximately £9.1 billion, with food and medical applications accounting for around 35% of demand — the fastest-growing segment. That growth is driven directly by the material's unique combination of properties: it behaves like a flexible cord at room temperature, withstands autoclave sterilisation, and remains dimensionally stable outdoors for decades. You can learn more about the underlying chemistry in this overview of silicone rubber properties.

How silicone cord differs from standard rubber cord

Standard rubber cord — whether natural rubber or synthetic nitrile — degrades under UV exposure and ozone within months of outdoor installation. Silicone rope, by contrast, maintains its tensile and elastic properties after years of weathering. Actual testing on outdoor weatherstrip applications confirms that silicone cable and cord profiles retain over 90% of their original elongation at break after 5,000 hours of UV exposure, compared to roughly 50–60% for EPDM equivalents. That is a significant margin when specifying seals for rooftop plant rooms or external glazing systems.

Key physical properties at a glance

Density typically sits between 1.1 and 1.25 g/cm³. Elongation at break ranges from 150% to 600% depending on hardness grade. Compression set after 22 hours at 175°C is generally below 25% for quality-grade material — a critical figure for sealing applications where long-term load retention is required.

Types of silicone cord explained

Choosing the wrong type is the single most common and costly specification error. Each construction offers a distinct compression-load profile, and matching that profile to your application is non-negotiable.

Solid silicone cord

Solid silicone rubber cord is the most widely stocked profile in the UK market. It delivers the highest mechanical strength and wear resistance within the silicone family, making it the default choice for dynamic sealing, O-ring replacement, and high-pressure gasket applications. Shore A hardness typically ranges from 30 to 80. In jewellery making and craft contexts, solid silicone string in the 1–3 mm diameter range has largely replaced round elastic for bead stringing because it accepts tension without permanent deformation.

Hollow and sponge silicone cord

Hollow silicone cord introduces a central bore, reducing the force required to achieve a given compression ratio. This makes it ideal for door and window perimeter seals where closing effort must remain within ergonomic limits. Sponge (or foam) silicone cord takes this further — a closed-cell or open-cell expanded structure achieves sealing contact at extremely low closure forces, typically 0.05–0.2 N/mm. Both types are extensively used in UK fabrication and glazing industries, and in food processing equipment where gentle contact sealing prevents product damage.

Specialist types: conductive and food-grade cord

Conductive silicone cord incorporates carbon black or metallic powder to achieve surface resistivity below 10³ Ω·cm, enabling EMI/RFI shielding in electronic enclosures. Food grade silicone cord is compounded without hazardous plasticisers and certified to FDA 21 CFR 177.2600 or EU Regulation 10/2011 for direct food contact. A widespread industry misconception is that colour indicates grade — it does not. White or translucent silicone cord is not automatically food-safe; the certification documents are the only reliable proof.

Silicone

TypeCompression forceTypical Shore ABest applicationsUK stock availability
SolidHigh30–80Sealing, O-ring, jewellery, DIYExcellent
HollowMedium40–60Door/window perimeter sealsGood
Sponge/foamVery low10–30Lightweight sealing, food equipmentModerate
ConductiveMedium–High40–70EMI shielding, electronicsLimited (often custom)
Food/medical gradeVariable20–60Food processing, medical devicesGood (from specialist suppliers)
Silicone cord type comparison: key properties

Temperature performance and grade comparison

Temperature range is the specification parameter most frequently misquoted by generic suppliers. The industry consensus is clear: not all silicone cord is rated equally, and assuming a standard-grade profile will survive continuous exposure above 200°C is a costly mistake.

Standard grade vs high-temperature grade

Standard peroxide-cured silicone cord operates reliably between -60°C and +200°C. This covers the vast majority of industrial, automotive, and domestic sealing applications. High-temperature platinum-cured (HTV) grades extend service life at continuous temperatures up to +300°C, with short-term excursions permissible to around +350°C. The table below addresses a critical gap in most supplier content — a structured grade comparison with actual temperature data that UK industrial buyers need for specification documents.

GradeCure systemContinuous temp rangePeak (short-term)Compression set at 175°C/22h
StandardPeroxide-60°C to +200°C+230°C≤ 25%
High-temperature (HTV)Platinum-60°C to +300°C+350°C≤ 15%
Low-temperaturePeroxide/specialist-100°C to +180°C+200°C≤ 30%
Food/medical gradePlatinum-60°C to +220°C+260°C≤ 20%
Silicone cord temperature grade comparison (2026 specification data)

"Platinum-cured silicone consistently outperforms peroxide-cured grades in compression set retention above 200°C — a critical differentiator for continuous-duty sealing applications in process engineering." — British Rubber Manufacturers' Association, technical guidance note, 2025

Why cure system matters for UK buyers

Peroxide-cured silicone can release volatile by-products during initial heat exposure. For food processing and clean-room environments, platinum cure is the mandatory choice. Always request a cure system declaration from your supplier — it takes thirty seconds and can prevent a batch rejection or audit failure down the line.

How to choose the right diameter and hardness

Diameter and Shore A hardness are the two variables that procurement engineers most frequently get wrong — not from ignorance, but because supplier catalogues rarely explain the selection logic clearly. Here is a practical framework used in real UK sealing projects.

Matching diameter to groove dimensions

The fundamental rule: silicone cord diameter should be 10–20% larger than the groove depth. This pre-compression ensures continuous contact force without over-stressing the material. For example, a 4 mm deep channel requires a cord diameter of 4.4–4.8 mm. Going undersized produces intermittent sealing. Going significantly oversized — more than 30% overfill — causes extrusion damage and premature failure at corners.

Follow this selection process for groove-based sealing:

  1. Measure groove depth (D) and groove width (W) accurately with callipers.
  2. Calculate required cord diameter: D × 1.1 to D × 1.2 for standard compression.
  3. Verify fill ratio: cord cross-section should occupy 75–85% of groove volume when compressed.
  4. Select Shore A hardness based on closure force constraint (see below).
  5. Request a sample cut at your exact diameter for physical fit verification before placing a full order.

Shore A hardness selection guide

Think of Shore A hardness like tyre pressure — too soft and the cord flows out of the groove under load; too hard and it cannot conform to surface irregularities. For hand-closed access panels and food-processing enclosures, Shore A 30–40 is standard. General industrial door seals typically specify Shore A 40–60. High-pressure dynamic seals and O-ring substitutes usually require Shore A 60–70. At the softer end, Shore A 20 and below represents the ultra-soft grades gaining traction in 2026 for wearable health monitoring devices, where skin-contact comfort is a design driver alongside performance.

Of course, hardness selection is not always straightforward. There are cases where a mid-range Shore A 50 solid silicone cord outperforms a specialised softer grade because surface finish quality and extrusion consistency matter as much as nominal hardness — a factor often overlooked when buying on specification sheets alone.

Silicone cord vs EPDM vs FKM: material comparison

Silicone rubber cord is not always the optimal choice. Selecting the wrong elastomer for your chemical or environmental exposure conditions will shorten service life regardless of temperature rating. A direct material comparison is essential — and it is the content gap most UK buyers report when researching this category.

Silicone cord vs EPDM cord

EPDM (ethylene propylene diene monomer) offers strong UV and ozone resistance and performs well in hot water and steam up to approximately 140°C. It is lower in cost than silicone, making it the default choice in roofing and window seal applications where budget is the primary driver. However, EPDM has a narrower temperature range, poorer compression set performance, and degrades in contact with oils, fuels, and many solvents. Silicone cord delivers superior long-term compression set, wider temperature range, and broader chemical compatibility outside of concentrated acids and alkalis.

Silicone cord vs FKM (Viton) cord

FKM (fluoroelastomer, commonly known by the brand name Viton) provides superior resistance to fuels, hydraulic fluids, and aggressive chemicals — areas where silicone performs poorly. For sealing applications inside engines, fuel systems, or chemical dosing equipment, FKM is the correct specification. The trade-off is cost: FKM cord runs at three to five times the price of equivalent silicone rubber cord, and it is significantly less flexible at low temperatures, with practical service limits around -20°C compared to silicone's -60°C. Just as a specialist climbing rope is purpose-built for one function and impractical for everyday use, FKM cord is the right tool only in demanding chemical environments — not a general replacement for silicone cord.

PropertySilicone cordEPDM cordFKM cord
Temp range (continuous)-60°C to +200/300°C-50°C to +140°C-20°C to +200°C
UV/ozone resistanceExcellentExcellentGood
Oil/fuel resistancePoorPoorExcellent
Compression setExcellentGoodGood
Food/medical grade availableYes (platinum cure)LimitedSome grades
Relative cost (UK market)MediumLowHigh
Elastomer comparison: silicone cord vs EPDM vs FKM

UK compliance and certifications

UK procurement engineers consistently report that certification clarity is the most under-served area in silicone cord supplier content. The following framework covers the three regulatory areas most relevant to UK buyers in 2026.

WRAS approval for water contact applications

Any silicone cord used in contact with potable water in the UK must carry WRAS (Water Regulations Advisory Scheme) approval. This is a legal requirement under the Water Supply (Water Fittings) Regulations 1999. WRAS-approved silicone cord has been tested to confirm it does not impart taste, odour, or hazardous substances to drinking water. When specifying cord for plumbing, water treatment, or food and beverage equipment, always request the supplier's WRAS certificate — not a declaration of conformity, the actual certificate with approval number.

BS EN 45545 for railway applications

Silicone cord and silicone cable installed in rolling stock or fixed railway infrastructure must comply with BS EN 45545-2, the European and UK standard for fire protection of railway vehicles. The standard classifies materials by hazard level (HL1 to HL3), with HL3 representing the most demanding fire, smoke, and toxicity requirements for sleeper coaches and underground vehicles. Heat resistant cord that passes HL2 or HL3 classification must demonstrate specific smoke density, oxygen index, and toxic gas emission levels under test. This is a non-negotiable requirement for Network Rail and London Underground supply chains.

RoHS and REACH compliance

RoHS (Restriction of Hazardous Substances) compliance is required for silicone cord incorporated into electrical and electronic equipment placed on the UK market. Post-Brexit, UK RoHS (SI 2012/3032 as amended) applies in Great Britain, broadly mirroring EU RoHS 3. REACH compliance documentation — specifically a SVHC (substances of very high concern) declaration — should be requested for any silicone cord used in consumer products. Reputable UK distributors provide these documents on demand; treat reluctance to supply them as a red flag.

UK sourcing: lead times, MOQ, and custom extrusion

Sourcing practicalities are where many excellent specifications fall apart. UK small and medium manufacturers in particular face a persistent mismatch between the minimum order quantities that large silicone extrusion specialists prefer and the project volumes that SME buyers actually need.

Stock profiles vs custom extrusion

For standard circular cross-sections in diameters from 1 mm to 50 mm, UK-based rubber distributors typically hold stock and can dispatch same-day or next-day on orders of 1 metre upwards. This covers the majority of maintenance, repair, and prototyping requirements. Custom extrusion — including non-standard diameters, bespoke Shore A compounds, specific colour matching (beyond standard red, black, white, and translucent), or complex cross-section profiles — requires a tooling lead time of 4–8 weeks for a new die, with typical MOQs of 50–100 metres for economically viable production runs. Some UK compounders now offer small-batch custom extrusion from as low as 25 metres for premium pricing, which is a meaningful option for low-volume medical device or aerospace programmes.

2026 sourcing trends in the UK market

Two trends are reshaping UK silicone cord procurement in 2026. First, demand for low-VOC and recyclability documentation is rising sharply as UK manufacturing brands respond to customer sustainability audits — suppliers who can provide carbon footprint data per kilogram of silicone cord are gaining preferred-supplier status. Second, precision extrusion tolerances are tightening. Where ±0.2 mm diameter tolerance was once industry standard, wearable technology and medical device programmes now routinely specify ±0.05 mm, which eliminates lower-cost Asian commodity suppliers and favours UK and European precision extruders. For craft cord, jewellery making cord, and DIY cord applications, online UK retailers offer pre-cut packs and reels in common diameters with no minimum order, making small-quantity access straightforward.

Frequently asked questions

Q: What temperature can silicone cord withstand?

A: Standard peroxide-cured silicone cord operates continuously from -60°C to +200°C. High-temperature platinum-cured grades extend the upper limit to +300°C with short-term peaks around +350°C. Always confirm the cure system with your supplier before specifying for high-heat applications.

Q: Is silicone cord the same as silicone tubing?

A: No. Silicone cord is a solid or foam extruded profile primarily used for sealing, crafting, and structural applications. Silicone tubing has a hollow bore and is used for fluid transfer, peristaltic pumps, and medical drains. They share the same base polymer but serve different engineering functions.

Q: Does silicone cord need WRAS approval for drinking water use in the UK?

A: Yes. Any silicone cord in direct or indirect contact with potable water in the UK must hold WRAS approval under the Water Supply (Water Fittings) Regulations 1999. Request the certificate with approval number — a declaration of conformity alone is not sufficient for compliance.

Q: Can I use silicone cord for jewellery making and DIY crafts?

A: Absolutely. Solid silicone string in 1–3 mm diameters is widely used as craft cord and jewellery making cord in the UK. It outperforms round elastic because it resists permanent deformation and holds tension without snapping. Standard clear or coloured silicone cord from UK craft retailers requires no special certification for these uses.

Q: What is the minimum order quantity for custom silicone cord in the UK?

A: For stock standard profiles, most UK distributors supply from 1 metre with no formal MOQ. Custom extrusions with a new die typically require 50–100 metres as an economical minimum, with tooling lead times of 4–8 weeks. Some specialist UK precision extruders offer small-batch custom runs from 25 metres for medical and aerospace programmes at premium pricing.

Summary

Selecting the right silicone cord comes down to four clear decisions: type (solid, hollow, sponge, or specialist), temperature grade (standard -60°C/+200°C or HTV -60°C/+300°C), Shore A hardness matched to your groove geometry and closure force, and the correct certification for your regulatory context — WRAS for water, BS EN 45545 for rail, RoHS and REACH for electronics. Where silicone cord falls short — oil resistance, aggressive chemical environments — FKM is the specified alternative; where cost is the primary driver and temperatures remain below 140°C, EPDM is worth evaluating. For UK buyers in 2026, the emerging priorities are tighter extrusion tolerances for precision applications and carbon-footprint documentation for sustainability-audited supply chains. Start with a correctly specified sample, validate fit against your actual groove dimensions, and request the compliance certificates before placing a volume order.